Friday, December 09, 2016

Jepp I/C 5: maneuvers full/partial panel, compass and timed turns, plus ILS 35R


We had a very cold but pleasant start to the morning, with 34 degrees and a 12kt crosswind.  I proved pretty much right off the bat that 3.5 weeks between flights is enough time to build up some dust.  Notably, I failed to drain the nose sumps and didn't catch that my seatbelt was unbuckled until pre-takeoff check!  Good gravies!  Checklist checklist checklist!

17R/35L was closed today, so all the planes were on 35R.  We followed a Southwest jet and a Gulfstream down the taxiway, with a reminder from Mark to use proper crosswind inputs while taxiing -- dive away from a wind from behind, up and into a wind from ahead.  I did our runup, and we were cleared to depart.  It was a very brief time before being handed over to departure, and she almost immediately gave us the freedom of own navigation.  That's when the foggles went on...

Level at 3000' we began maneuvers.  Constant rate descents and ascents, using the VSI as primary for pitch and aiming for 500 fpm (and accounting for the +100 error on the needle) and any speed we wanted (so ASI was primary for power, keep it in the green).  Those are fine, just need more practice to get the right pitch/power settings more directly.

Turns by mag compass.  Mark failed the vacuum system, which takes out the attitude indicator and the DG.  This is why the mag compass is required equipment on all planes.  :)  It's really just fine as long as you remember COSUN -- compass overshoots south, undershoots north.  So when turning right to a heading of 180, you actually turn roughly to indicated 210 because of compass error; once you roll out, it swivels back.  Roughly speaking, it's a 30-degree overshoot for a desired heading of 180; 20 degrees for headings of 150 and 210; 10 degrees for headings of 120 and 240; and right on target for due east and west.   It's the same gradients for turning to the north except it's an undershoot situation; if you want a right turn to a heading of 360, you turn roughly to  330, and when you roll out it keeps swiveling a bit.  This varies by latitude and those numbers actually apply for 40N; we're at 30N so the error is a tad less.  But those easy-to-remember rules get you pretty close and then the minor correction needed to capture the desired heading is easy.

That's how the mag compass behaves in a turn.  The other thing to know about compass error is how it behaves during straight-and-level flight, meaning holding heading and altitude.  Unaccelerated, it's solid!  Accelerated, ANDS -- accelerate north, decelerate south.  When holding altitude and heading, adding throttle to accelerate will induce a temporary indication of a turn toward the north; pulling back on the throttle induces a temporary indication of a turn to the south.  NBD.

Next was timed turns, which I hadn't done before.  The idea here is that a standard rate turn, easily achievable using the turn coordinator (provided you don't have electrical failure), which means at the proscribed bank you'll complete a full 360-degree turn in two minutes.  That's 3 degrees per second.  If you need to turn 60 degrees, roll into the turn and time for 20 seconds.  When making smaller turns, say less than 15 degrees, you use a half-standard rate turn (1.5 degrees per second); a 15-degree turn would take 10 seconds.  That's all well and good, just requires a little mental nimbleness.  I also had two areas to improve that will help make the timing method result in rollout closer to desired heading:  roll in faster and keep the ball centered.  The first turn was the worst, and I was about 15 degrees short of my target because of lolligagging into the turn and not using enough rudder.  Subsequent timed turns were better.

All of the turns were fine, but I need to keep my scan going a little faster.  I wavered on my altitude, but kept it usually within 100'.  I find I have a tendency to climb during turns and need to work on that.

We did combinations of these maneuvers on partial panel.  It's fine, just needs practice!  

Recovery from unusual attitudes on partial panel was fine, too.  For this exercise, you look down, optionally with eyes closed, the idea being to become completely detached from the state of the plane while the instructor puts it into any type of configuration.  Then you look up, take the controls, and recover.  If the plane is descending, first you level the wings, then stop the descent, then return to assigned heading and altitude.  If the plane is climbing, first you level the nose (don't want to be near a stall), then level the wings and return to the desired state.

Lastly we decided to request the ILS back into KAUS.  We were still 33 nm out, so had lots of time to brief the approach and get set up.  We loaded the I-HCE localizer into NAV1, but were to far to ident.  We also loaded it into the GPS (whose database expired two days ago and so would not be legal for RNAV approaches but can still be used for DME, which this ILS has on the plate).  Next, Mark dialed in the final approach course of 353 on the NAV1 CDI, briefed the missed (DA ~700', climb to 1000', climbing right turn to 1500', head to CENTEX VOR), They vectored us to intercept and cleared us somehow....  my memory is fuzzy here.  My brain was definitely saturated and I was feeling the workload, and that was with Mark doing com and nav!  Maintaining proficiency will be so important.  

Anyway, we intercepted and had to chase the radial a little to get on it, but once established I'd say it went fairly well.  It wasn't close to the standard I'm aiming for, but it's early in the process and will get better.  That relatively straight blue line on the left is the approach.  The closer we got, and the squirrelier the needles got, the more I was getting anxious about the transition to visual and about configuring for landing.  They had asked us to keep up our speed since half the runways were closed and little ol' student flight with two souls might be holding up commercial flights with a hundred souls.  I was getting concerned about slowing for flaps and all that, and at one point put out the first notch without first checking the airspeed, which was still over 120, so I pulled them right back in.

Eventually that notch of flaps did get used, and we were quite fast over the numbers.  There was a touch of crosswind, and it was nice and steady, so for the first time ever I felt competent and successful in maintaining runway alignment, pretty close to centerline even!  We floated and flared forever.  Seriously, forever.  And when I let us down, it was too early and we were still too high and worse we were still too fast, so Mark asked for the controls and got us right back up into ground effect for more forever.  I'm going to have to look at the track log and see just was our speed was over the runway.

But that was it!  Other than that bounce, it was a very good flight!  I felt cautiously competent, understood what we were doing, executed pretty well (practice will fine-tune it), learned some things and solidified some other knowledge and feelings for flight.

We did not do full-panel steep turns, slow flight or stalls this time out since we got off to kind of a late start.  Next time we'll have to get those in, and it's on to Jepp I/C 6: partial-panel steep turns, slow flight and stalls with review of everything else we've done so far (mainly from today's flight).  After that, we're pretty much done with the aviating-by-instrument part and will start incorporating navigation, beginning with using VORs and talking about NDBs (since the flight school fleet doesn't have ADFs).